$z[0][4]['name']="typeurl"; $z[1]=Array("field","",51,80); $z[1][4]['name']="typename"; $z[2]=Array("field","",82,111); $z[2][4]['name']="typename"; $z[3]=Array("channel"," [field:typename/] ",151,280); $z[3][4]['type']="son"; $z[3][4]['noself']="yes"; ?>]="son"; $z[3][4]['noself']="yes"; ?>$z[0][4]['name']="typeurl"; $z[1]=Array("field","",51,80); $z[1][4]['name']="typename"; $z[2]=Array("field","",82,111); $z[2][4]['name']="typename"; $z[3]=Array("channel"," [field:typename/] ",151,280); $z[3][4]['type']="son"; $z[3][4]['noself']="yes"; ?>]="son"; $z[3][4]['noself']="yes"; ?>$z[0][4]['name']="typeurl"; $z[1]=Array("field","",51,80); $z[1][4]['name']="typename"; $z[2]=Array("field","",82,111); $z[2][4]['name']="typename"; $z[3]=Array("channel"," [field:typename/] ",151,280); $z[3][4]['type']="son"; $z[3][4]['noself']="yes"; ?>]="son"; $z[3][4]['noself']="yes"; ?>$z[0][4]['name']="typeurl"; $z[1]=Array("field","",51,80); $z[1][4]['name']="typename"; $z[2]=Array("field","",82,111); $z[2][4]['name']="typename"; $z[3]=Array("channel"," [field:typename/] ",151,280); $z[3][4]['type']="son"; $z[3][4]['noself']="yes"; ?>]="son"; $z[3][4]['noself']="yes"; ?>$z[0][4]['name']="typeurl"; $z[1]=Array("field","",51,80); $z[1][4]['name']="typename"; $z[2]=Array("field","",82,111); $z[2][4]['name']="typename"; $z[3]=Array("channel"," [field:typename/] ",151,280); $z[3][4]['type']="son"; $z[3][4]['noself']="yes"; ?>]="son"; $z[3][4]['noself']="yes"; ?>$z[0][4]['name']="typeurl"; $z[1]=Array("field","",51,80); $z[1][4]['name']="typename"; $z[2]=Array("field","",82,111); $z[2][4]['name']="typename"; $z[3]=Array("channel"," [field:typename/] ",151,280); $z[3][4]['type']="son"; $z[3][4]['noself']="yes"; ?>]="son"; $z[3][4]['noself']="yes"; ?>$z[0][4]['name']="typeurl"; $z[1]=Array("field","",51,80); $z[1][4]['name']="typename"; $z[2]=Array("field","",82,111); $z[2][4]['name']="typename"; $z[3]=Array("channel"," [field:typename/] ",151,280); $z[3][4]['type']="son"; $z[3][4]['noself']="yes"; ?>]="son"; $z[3][4]['noself']="yes"; ?>$z[0][4]['name']="typeurl"; $z[1]=Array("field","",51,80); $z[1][4]['name']="typename"; $z[2]=Array("field","",82,111); $z[2][4]['name']="typename"; $z[3]=Array("channel"," [field:typename/] ",151,280); $z[3][4]['type']="son"; $z[3][4]['noself']="yes"; ?>]="son"; $z[3][4]['noself']="yes"; ?> 折弯机模具使用规范_折弯机模具,折弯机刀具,数控折弯机模具-武汉折弯机模具|青岛折弯机模具|山东折弯机模具
0512-57674877
banner2

咨询热线

0512-57674877
地址:昆山市张浦镇同舟路38号
邮箱:cnamada@163.com

技术园地

当前位置:主页 > 技术园地 >

折弯机模具使用规范

发布时间:2016/09/20 点击量:

折弯机模具的使用规范
1、接通折弯机的电源,扭转钥匙开关,按下油泵启动,折弯机油泵开始转动,此时机器还未开始工作。
2、行程调节,在正式开始用折弯机模具进行折弯工作时需要试车。折弯机上模下行至最底部时必须保证有一个板厚的间隙。否则会对模具和机器造成损坏。行程的调节也是有电动快速调整和手动微调。
3、折弯机模具槽口选择,一般要选择板厚的8倍宽度的槽口。如折弯4mm的板料,需选择32左右的槽口。
4、检查折弯机上下模的重合度和坚固性;检查各定位装置是否符合被加工的要求。经常检查上、下模具的重合度;压力表的指示是否符合规定。
5、板料折弯时必须压实,防止板料在折弯时翘起伤害操作人员。
6、调板料压模时必须切断电源,停止运转后进行。
7、在改变可变折弯机下模的开口时,不允许有任何料与下模接触。
8、禁止使用折弯机模具折超厚的铁板或淬过火的钢板、高级合金钢、方钢和超过板料折弯机性能的板料,以免损坏机床。
9、关闭折弯机,要在两侧油缸下方的下模上放置木块将上滑板下降到木块上。先退出控制系统程序,后切断电源。

上一篇:折弯机的操作流程

下一篇:没有了

返回

地址:昆山市张浦镇同舟路38号   电话:0512-57674877    版权所有;昆山阿姆达精密刀具有限公司
技术支持:腾达电子商务    ICP备案编号:苏ICP12345678